American Bass DX15

Do any of you know how much airspace 4 american bass dx15's would need? Ported or sealed? I havent been able to find much info on them. Iv put 4 of them in a sealed box with around 12cubes before and it did pretty good. But Iv been trying to find some kind of specs with not much luck

[You must be registered and logged in to see this image.]

if your talking about the same american bass speakers above.. 1 of them requires 267.2687 ft cubed
So 4 or them would require 1069.0748 ft cubed for a perfect enclosure. Building them smaller than that would equal not using them to their full potential.

This would equal having a box built 10 foot long, wide and tall or (cubed).
I did a calculation on them, and it looks like they are better for sealed enclosures.. cause at 28hertz and a QeS of 0.656 is comes out to an EBP of 42.68

You can find more stuff about this at this link David
[You must be registered and logged in to see this link.]
and at here
[You must be registered and logged in to see this link.]

You can figure volumes at this site..
[You must be registered and logged in to see this link.]


The specs for them is below...

SIZE(IN) 15
IMP 4
RDC 2.8
LEVC(MH) 4.602
FO(Hz) 28
SD(msqM) 76.45
BLTM 12.329
QMS 4.792
QES 0.656
QTS 0.577
n(%) 0.598
SPL(Db) 93
VAS(L) 134
CMS(Um/n) 161.2
MMS(g) 204.6
VC 2
MAGNET(OZ) 100
XMAX(+/-mm) 10
POWER(RMS) 350
POWER(MAX) 700
F RANGE(Hz) <300
MAGNET DEPTH(MM) 192
MAGNET DEPTH(INCH) 7.6
Found here... [You must be registered and logged in to see this link.]


* Ultra Thick Chrome-Plated Deep Bottom Basket.
* NT Multilayer Foam Surround for Better Stable Linear Exclusion.
* Stiff and Rigid non-press Paper Cone.
* Inverted Dust Cap further increases Cone's resistance to flex under Pressure
* Dual Black Mirror Tinsel Lead Wires.
* Sleeved High Power Tinsel Lead Wires to resist Lead breakage.
* Blackened Motor Parts for Superior Heat Dissipation & Long Life
* Hi-Temp Anodized Aluminium Voice Coil Bobbin with Nonex Protection.
* Ultra-Length Voice Coil for High excursion without Distortion.
* Hyper extended Pole Piece Increases Accuracy, raises Induction.
* Special Cooling Vents of Deep Bumped Back Plate to Increase Power Handling.
* Uni-Rubber Gasket for Airtight Seal in Mounting.
* Rubber Magnet Boot Protects Magnet.
* Single Voice Coil 4 OHM

* Single Voice Coil
* 100 Ounce Magnet

I appreciate it

Is that what you were looking for? Just trying to help out a fellow member.

yeah. im not going to be able to get what they need but it should be good enough. Mecca dont come around here anymore so its not so critical. I personally am a fan of the older subs. I have two 18" treos in my bravada. And I have two planet audio fu 18's that were in my s10. they may go back in. I havnt decided

i can appreciate someone that loves bass- i've only worked with kicker and pioneer, i need a system to put in my trailblazer now though i have 2 speakers that are blown and im wanting to revamp it- lol

It hits pretty hard

[You must be registered and logged in to see this image.]

Those look huge... WOW, you build the box? if so great job!

Thank you sir