FCP HomeHomeRegisterLog in

Share
 

 Measuring Tire Tread Depth with a Coin

Go down 
AuthorMessage
Blacked Out
5000 Post Club
5000 Post Club
Blacked Out


Measuring Tire Tread Depth with a Coin Empty
PostSubject: Measuring Tire Tread Depth with a Coin   Measuring Tire Tread Depth with a Coin I_icon_minitimeWed Jun 15, 2011 10:49 am

U.S. coins can be substituted for a tire tread depth gauge as tires wear to the critical final few 32nds of an inch of their remaining tread depth.

Place a penny into several tread grooves across the tire. If part of Lincoln's head is always covered by the tread, you have more than 2/32" of tread depth remaining.

[You must be registered and logged in to see this image.]

2/32" remaining tread depth

Place a quarter into several tread grooves across the tire. If part of Washington's head is always covered by the tread, you have more than 4/32" of tread depth remaining.

[You must be registered and logged in to see this image.]

4/32" remaining tread depth

Place a penny into several tread grooves across the tire. If the top of the Lincoln Memorial is always covered by the tread, you have more than 6/32" of tread depth remaining.

[You must be registered and logged in to see this image.]

6/32" remaining tread depth

Once you have determined the approximate remaining tread depth in the first location, you can complete your measurement of each tire by placing the coin into additional locations at lease 15 inches apart around the tire's central circumferential groove, as well as in its inner and outer grooves. This will help detect uneven wear caused by mechanical or service conditions.

The Law
According to most states' laws, tires are legally worn out when they have worn down to 2/32" of remaining tread depth. To help warn drivers that their tires have reached that point, tires sold in North America are required to have indicators molded into their tread design called "wear bars" which run across their tread pattern from their outside shoulder to inside shoulder. Wear bars are designed to visually connect the elements of the tire's tread pattern and warn drivers when their tires no longer meet minimum tread depth requirements.

Common Sense
However, as a tire wears it's important to realize that the tire's ability to perform in rain and snow will be reduced. With 2/32" of remaining tread depth, resistance to hydroplaning in the rain at highway speeds has been significantly reduced, and traction in snow has been virtually eliminated.

If rain and wet roads are a concern, you should consider replacing your tires when they reach approximately 4/32" of remaining tread depth. Since water can't be compressed, you need enough tread depth to allow rain to escape through the tire's grooves. If the water can't escape fast enough, your vehicle's tires will be forced to hydroplane (float) on top of the water, losing traction.

If snow-covered roads are a concern, you should consider replacing your tires when they reach approximately 6/32" of remaining tread depth to maintain good mobility. You need more tread depth in snow because your tires need to compress the snow in their grooves and release it as they roll. If there isn't sufficient tread depth, the "bites" of snow your tires can take on each revolution will be reduced to "nibbles," and your vehicle's traction and mobility will be sacrificed. Because tread depth is such an important element for snow traction, winter tires usually start with noticeably deeper tread depths than typical All-Season or summer tires. Some winter tires even have a second series of "wear bars" molded in their tread pattern indicating approximately 6/32" remaining tread depth to warn you when your tires no longer meet the desired tread depth.
Back to top Go down
http://www.friendlycarpeople.com
 
Measuring Tire Tread Depth with a Coin
Back to top 
Page 1 of 1
 Similar topics
-
» Turf Tire Cutting
» What kind a tire would be the best for offroading but the least strain on my transaxle?
» FS: Nitto Terra Grappler (single tire) - 265/70/17
» In depth article on Elena Berezhnaya
» drifter float what depth to fish at ???

Permissions in this forum:You cannot reply to topics in this forum
 :: Cars, Trucks, Vans, & SUVs :: Tires & Wheels-
Jump to: